Holy fuck that seems like a tedious, difficult, messy job. I’ve also never heard of it, and I feel like the homeowners I know would have bitched about it to me before if they had to do it. I looked it up, and there’s all sorts of scenarios in which they might not have to do that (anode rods and tankless water heaters both seem pretty cool and there are services for it), but I might just send out a couple of texts. Water heaters are nothing to fuck with.
It’s tedious, but it’s mostly just a matter of waiting for the water to heat back up afterwards.
Unplug the heater, then run the bathtub until you’re out of hot water. Turn off the bathtub, and turn off the water supply going into the heater. Attach a garden hose to the bottom of the heater, and run it to a drain somewhere. Turn the hot water on somewhere like a sink, to provide a vent to the system; It won’t run because the supply is turned off, but it’ll at least allow air into the system for when you drain the heater. Use the spigot at the bottom of the heater to drain it.
Be prepared for a gross rush of water at first, because all of the sediment and rust will have settled to the bottom of the heater where the spigot is. Once it’s drained, you can do whatever maintenance you need. For instance, you probably need to replace the cathode rod, which is designed to wear away over time to protect the rest of the heater from corrosion.
To do a final flush, you can open the water inlet at the top of the tank. It’ll help drain any last remaining sediment out of the tank. Then turn off the water inlet, turn off the spigot, disconnect the hose, and leave the sink tap open while you refill the tank with fresh water.
The whole process only takes like 30 minutes, and then you’re just waiting for the heater to come back up to temperature afterwards.
Wow thanks for the info. My heater tank just shit the bed a month ago, flooding water all over my unfinished cave of a basement. I rent this place, so all in all for me it was great. My landlord replaced it with a pretty decent and bigger tank, the plumber replaced a lot of our 100 year old pipes with new brass, so now my wife and I can do showers back to back in the winter with hot water.
Hopefully we’ll become homeowners in 2025 so I’m saving this for the future.
Edit: I forgot! We had nuts water pressure before,125 psi, but the plumber said he had to put a limiter on by law. Probably will save us a bit of money.
If it has a valve on the outlet of the water heater, you can close that and flush cold water through the heater and out the bottom drain by opening the drain. This will also have more pressure and volume of water to flush with.
Nope. That’s inside the engine core. This is just an aerodynamic tail cone for the engine that serves to streamline exhaust airflow and maintain cross sectional area for the exhaust where it exits the engine. Makes for less turbulence and noise.
on what? the fuck are we looking at?
That’s a handprint on one of the many parts of a jet engine that get hot. Extremely hot
deleted by creator
Holy fuck that seems like a tedious, difficult, messy job. I’ve also never heard of it, and I feel like the homeowners I know would have bitched about it to me before if they had to do it. I looked it up, and there’s all sorts of scenarios in which they might not have to do that (anode rods and tankless water heaters both seem pretty cool and there are services for it), but I might just send out a couple of texts. Water heaters are nothing to fuck with.
It’s tedious, but it’s mostly just a matter of waiting for the water to heat back up afterwards.
Unplug the heater, then run the bathtub until you’re out of hot water. Turn off the bathtub, and turn off the water supply going into the heater. Attach a garden hose to the bottom of the heater, and run it to a drain somewhere. Turn the hot water on somewhere like a sink, to provide a vent to the system; It won’t run because the supply is turned off, but it’ll at least allow air into the system for when you drain the heater. Use the spigot at the bottom of the heater to drain it.
Be prepared for a gross rush of water at first, because all of the sediment and rust will have settled to the bottom of the heater where the spigot is. Once it’s drained, you can do whatever maintenance you need. For instance, you probably need to replace the cathode rod, which is designed to wear away over time to protect the rest of the heater from corrosion.
To do a final flush, you can open the water inlet at the top of the tank. It’ll help drain any last remaining sediment out of the tank. Then turn off the water inlet, turn off the spigot, disconnect the hose, and leave the sink tap open while you refill the tank with fresh water.
The whole process only takes like 30 minutes, and then you’re just waiting for the heater to come back up to temperature afterwards.
Wow thanks for the info. My heater tank just shit the bed a month ago, flooding water all over my unfinished cave of a basement. I rent this place, so all in all for me it was great. My landlord replaced it with a pretty decent and bigger tank, the plumber replaced a lot of our 100 year old pipes with new brass, so now my wife and I can do showers back to back in the winter with hot water.
Hopefully we’ll become homeowners in 2025 so I’m saving this for the future.
Edit: I forgot! We had nuts water pressure before,125 psi, but the plumber said he had to put a limiter on by law. Probably will save us a bit of money.
deleted by creator
If it has a valve on the outlet of the water heater, you can close that and flush cold water through the heater and out the bottom drain by opening the drain. This will also have more pressure and volume of water to flush with.
Jet engine burner can
Nope. That’s inside the engine core. This is just an aerodynamic tail cone for the engine that serves to streamline exhaust airflow and maintain cross sectional area for the exhaust where it exits the engine. Makes for less turbulence and noise.
Nerd.
But yes, correct.